Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in Renton?
Gate repair in Renton typically costs $185 to $850, with most residential fixes landing between $250 and $475. A simple sensor realignment or remote receiver swap sits at the low end. A control board replacement or a heavy slide-gate motor rebuild pushes toward the top. Commercial swing and slide systems, including DoorKing entry setups at multi-tenant properties, often run $600 to $1,800 depending on the operator and what failed.
Those are typical ranges, not quotes. The written estimate we give you after we look at the gate sets the final price. We specialize exclusively in gates: repair, electric systems, and installation, so the diagnosis comes from someone who works on these operators every day.
Key Takeaways
- Most home gate repairs in Renton run $185 to $850; commercial work runs higher.
- Operator brand matters: a Mighty Mule DIY-grade arm prices differently from a commercial DoorKing system.
- Our technicians have up to 8 years of experience, and we’re familiar with LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
- Free estimates. Call (866) 293-5161. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Gate Repair Cost Breakdown (2026)
A broken gate gives you a security gap the moment it stops closing. Here’s how the numbers break out for the Renton market in 2026. Use these as planning ranges, not a fixed price sheet.
| Repair | Typical Renton Range | What’s Involved |
|---|---|---|
| Safety sensor realignment or replacement | $185 – $340 | Photo-eye, loop detector, or edge sensor diagnosis and replacement |
| Remote and receiver / keypad programming | $150 – $295 | New remotes, receiver swap, keypad re-pair, code reset |
| Control board replacement | $275 – $650 | Board diagnosis, replacement, and re-teach of limits and travel |
| Swing gate arm or actuator replacement | $375 – $850 | Arm or actuator swap, mounting, re-calibration |
| Slide gate motor and operator repair | $400 – $1,200 | Motor, gear, or chain repair; track and roller service |
| Commercial / multi-tenant operator repair (DoorKing, FAAC, BFT) | $600 – $1,800 | Entry system, board, loop, and access hardware diagnosis |
| New gate installation (electric, residential) | $3,200 – $8,500 | Gate, operator, sensors, wiring, and setup |
| New gate installation (commercial swing or slide) | $8,000 – $22,000+ | Heavy gate, commercial operator, loop and safety hardware |
What pushes a bill up: the type of operator, whether parts are available for that brand, how much the gate itself has been stressed (a sagging slide gate that keeps jumping the track usually needs more than a motor swap), and whether it’s a residential driveway or a commercial entry. What pulls it down: a single failed component, a common brand we already know inside out, and a gate that was installed correctly to begin with. Commercial systems sit higher because the operator, the safety hardware, and the consequences of a bad fix are all bigger.
Repair or replace? We’ll tell you which one actually makes sense for your system. If the operator is sound and one part failed, repair wins. If the gate frame is bent, the track is worn through, and the motor is on its third fault, replacement is usually the cheaper path over the next few years.
What Affects Gate Repair Pricing in Renton
- The operator brand. A Mighty Mule or Ghost Controls driveway arm reads differently from a commercial FAAC or DoorKing system. Each brand has quirks, and knowing them shortens diagnosis and cuts repeat visits. We work with all nine of the major brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
- Electric versus manual. A manual gate with a broken hinge or latch is a simple mechanical fix. The moment you add an operator, control board, sensors, and wiring, the labor climbs. Electric and automated gate repair is a primary service here, not an add-on, so we diagnose the board and the motor instead of routing you elsewhere.
- Residential versus commercial. A private driveway gate is one thing. A multi-tenant entry with loop detectors, keypads, and a DoorKing call system is another. Commercial work takes longer to diagnose and test, and the parts cost more.
- What actually failed. Sensors and remotes are the low end. Motor assemblies and control boards sit in the middle. A slide gate that’s jumped the track or bent a panel adds structural work on top of the electrical fix.
- Gate condition and access. A gate that’s been dragging, sagging, or leaning for a while costs more to bring back than one that failed this week. Driveway slope, footing condition, and how the gate is mounted all affect the labor. Posts need proper footing depth; that’s part of what we check.
- Wiring and power. The operator’s wiring and power are where the real danger lives on an electric gate. We trace the low-voltage control wiring and check the supply, and we don’t cut corners on conduit that’s been exposed or chewed. That diagnostic time is part of the estimate.
Renton’s wet winters and damp shoulder seasons do the gate no favors. Water gets into enclosures, corrodes terminals, and finds the lowest point in a control box. That’s one reason a gate that worked fine in summer can fail in January. We look at the enclosure and the wiring as part of any diagnosis, because fixing the board without fixing the moisture path just puts you back here next season.
How to Save on Gate Repair
You can keep the bill at the low end of these ranges with a few practical moves.
- Get the free estimate in writing. Know the price before any work starts. The written estimate is what sets the final number, so there’s no surprise when the invoice arrives. Call (866) 293-5161.
- Fix the small thing before it becomes the big thing. A sensor that’s drifted out of alignment is a $185 to $340 fix. Left alone, a gate that keeps reversing can stress the motor and turn that into a $650 control-board job.
- Know your brand. Tell us the operator brand when you call. If you don’t know it, a photo of the control box and the arm or track helps us come prepared, which shortens the visit.
- Ask whether repair or replacement is the better call. Sometimes a $450 repair on a sound operator beats a $5,000 replacement. Other times the reverse is true. We’ll give you the straight answer either way.
- Keep the gate moving. A slide gate that runs on a clean track with intact rollers and a cleared path puts less strain on the motor and operator. Clearing debris from the travel path is free.
- Don’t let water sit in the enclosure. After a stretch of rain, check that the control box lid is seated and the conduit isn’t holding water. A dry enclosure is a longer-lived board.
We repair, we service the electric system, and we install, all with one point of contact from diagnosis through the finished job. No hand-offs between contractors, no one learning your brand on the clock.
FAQs – Gate Repair Cost
How much does gate repair cost in Renton?
Most gate repairs in Renton run $185 to $850, with a typical job landing between $250 and $475. Commercial and multi-tenant systems run higher, roughly $600 to $1,800, because the operator and safety hardware are heavier. Call (866) 293-5161 for an exact quote – estimates are free.
Is it cheaper to repair or replace a gate?
Repair is usually cheaper when the gate frame is sound and one component failed; that’s typically a $185 to $850 repair against a $3,200 to $8,500 new electric gate installation. Replacement wins when the frame is bent, the track is worn through, and the operator keeps failing. We’ll tell you which one actually makes sense for your system. Call (866) 293-5161 for a free estimate.
Does the operator brand change the price?
Yes. Brand affects parts cost and diagnostic time. Entry-level residential operators like Mighty Mule and Ghost Controls and commercial systems like DoorKing, FAAC, and BFT each have their own quirks, and knowing the brand shortens the diagnosis. We work with nine major brands, so the estimate reflects your actual system. Call (866) 293-5161.
What does an electric gate repair cost compared to a manual gate fix?
Electric gate repair typically runs $275 to $1,200 depending on whether it’s a sensor, a control board, or a motor assembly. A manual gate fix is usually simpler and cheaper. The jump is in the electronics: board, wiring, and sensors all add labor. Call (866) 293-5161 for an exact figure.
Can you come today?
Same-day service is often possible. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. Call (866) 293-5161 to get on the schedule.
What’s the most common reason an electric gate fails?
The most common failures we see are safety sensors knocked out of alignment, control boards damaged by moisture, and slide-gate motors that have been strained by a dirty track or worn rollers. Diagnostics start at the low end of our range and go up from there. Call (866) 293-5161 to book a look.
Do you install new gates too?
Yes. We handle gate repair in Renton and full gate installation, both residential and commercial. A new electric residential gate usually runs $3,200 to $8,500 installed; commercial swing or slide systems run higher. Call (866) 293-5161 for a free estimate.
Why a Gate Specialist Changes the Price
When a general handyman or a fence company looks at a broken gate, they often replace parts until it works. That’s how a $300 sensor problem becomes a $900 bill. We don’t do that. We specialize exclusively in gates, and we diagnose control boards, loop detectors, and motor assemblies rather than guess at them. From Ghost Controls driveways to FAAC commercial swing gates, it’s one team, full coverage.
That focus matters most on the electrical side. A gate operator that won’t open can be a dead remote, a bad receiver, a blown board, a stuck limit switch, or a motor drawing too much current. Each of those repairs sits in a different price bracket. The right diagnosis on the first visit is what keeps your cost at the low end of the ranges on this page, and it’s why we test the whole system, not just the part that obviously failed.
A safety note on the electrical side. The control wiring, the power supply, and the motor connections on an automated gate carry real current. A heavy swing or slide panel can crush a hand or a pet if it actuates unexpectedly. Slide gates that come off the track are a serious hazard. We recommend a trained professional for anything involving the operator’s wiring, power, or panel weight. Please don’t work on the electrical side of an automated gate yourself.
If your gate is failing, it’s worth looking at the broader options for gate repair, including electric and mobile gate work, before you commit to a replacement. We’ll walk you through both paths.
Get a Free Gate Repair Estimate in Renton
A malfunctioning gate is a security risk, and every day it sits open is a day your property is exposed. We diagnose it fast and fix it right. We already know your operator brand, whether it’s a LiftMaster residential arm or a DoorKing commercial entry, and our technicians have up to 8 years of experience working across all the major systems. Free estimates, upfront pricing, and one point of contact from the first call through the finished repair or installation.
Call (866) 293-5161 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Tell us the gate and the brand, and we’ll tell you what it takes to get it working again.
Pricing reflects the Renton market as of 2026. Gate Repair Renton offers free estimates – call (866) 293-5161.
Written by the team at Gate Repair Renton.
What Our Customers Say
"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
- David Park"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
- Christine Nguyen"Fixed the immediate problem. He was honest that the operator is near end of life and I should budget for a replacement, which I appreciate even if it wasn't what I wanted to hear."
- Renee Pruitt